Javascript Menu by Deluxe-Menu.com

dhs ELMEA tools Logo  
     
Aggregation TAPs

   

Albedo Telecom Net.Shark - ein portabler Aggregation-TAP

     

Der Net.Shark ist ein FPGA basierter, batteriebetriebener Netzwerk TAP und unterstützt 10/100/1000T (Kupfer SFP), sowie 1000X (optisches SFP) Schnittstellen. Die Hardware ist in der Lage Fullduplex Gigabit Linerate Daten ohne Einschränkungen in Bezug auf die Paketgrüsse zu verarbeiten.

Der TAP kopiert die Daten entweder transparent auf zwei Monitorports oder aggregiert die beiden Datenrichtungen auf einen Port, um Fullduplexanalysen zu ermüglichen, wenn nur ein Aufzeichnungsport zur Verfügung steht. 16 parallel verfügbare Filter zusammen mit der Aggreagtionsfunktion machen den Net.Shark zu einem idealen "Wireshark Partner" beim Troubleshooting an Gigabit Ethernet Links.

Features:

  • Batteriebetrieb, dadurch 100% autonom
  • Hardware (FPGA) performace (GigE Linerate)
  • Messports separat oder aggregiert
  • 16 parallele Filter für die Monitordaten

Filter:

  • Ethernet Source und Destination MAC Adressen
  • Ethertype Wert
  • VLAN-VID
  • VLAN-CoS
  • IP Source and Destination
  • IP Adressgruppen
 

Albedo Telecom Net.Shark
Albedo Telecom Net.Shark

Calnex Paragon brochurePDF Datasheet

  • alle Adress- und Filterwerte künnen zusätzlich über Masken erweitert werden Filter auf Protokollfelder oberhalb des IP Layers (TCP, UDP, Telnet, FTP, etc.)
  • DSCP Feld, Einzelwert oder Range
  • TCP/UDP Port, Einzelwert oder Range
  • Agnostics Filter: bestehend aus einer 16 Bits Maske und einem benutzerdefinierten Offset
  • Lawful Filter: 64 Byte Pattern match an jeder beliebigen Stelle in der Payload beginnend von einem Offset

arrow weitere Albedo Telecom Produkte...

     

   
Cubro Multilink Aggregation TAP
 

Multilink Aggregation TAP's combine up to 24 10/100 Base-T Links to a single Aggregation Monitor Port and an optical Link extension Port. It helps to save costs for Measuring and Monitoring Test Equipment.

Multilink Traffic Aggregation
Aggregation of up to 24 10/100 Base-T links in one 1000 Base-T Monitor Port. Also units with 4, 8, 12, 16, 20 and 24 Link-Aggregation are available.

LINKSAVE Function
Special LINK SAVE Function enables secure Network Links even if the power supply fails. So the TAP does not influence the network, even if it is not powered.

LED Indicators

  • LED's on the front panel indicates power-, link- and activity status.
  • Different Power Versions
  • 48V DC or 230VAC power supply versions
    available.
 

Cubro Multilink Aggregation TAP
Cubro Multilink Aggregation TAP

Link Extension
With help of the optional available Port Aggregator you can combine 4 Link Aggregation Taps to extend the total number of Links. So it is possible to aggregate up to 96 10/100 Base-T Links.

Rugged 19" Housing

  • Stable 19" Housing with precise connector
    labelling on front panel.
  • 19" 1U high (4, 8 or 12 Links)
  • 19" 2U high (16, 20 or 24 Links)

Link Extension

With help of the optional available Port Aggregator you can combine 4 Link Aggregation Taps to extend the total number of Links. So it is possible to aggregate up to 96 10/100 Base-T Links.

     

   
Cubro GBit Aggregation TAP
 

Cubro GBit Aggregation TAP
Cubro GBit Aggregation TAP

Want to monitor the traffic of an optical Gigabit Ethernet link with your existing monitoring equipment, which features only a 1000B-T electrical input? The 1GE Aggregation TAP is the right answer for this challenge. With its fully passive connection to the network it doesn't influence the traffic of the optical network link while still allowing full access to the traffic via the monitoring port.

Multimode and Singlemode
The network link can be either in Multimode (850/1300nm) or Singlemode (1310/1550nm). By default Cubro 1GE Converter TAPs are delivered with SC type connectors. Optional, the units can also be equipped with FC or LC connectors - according to your requirements.

 

Number of Monitoring Ports
By default Cubro 1GE Aggregation TAPs come with one monitoring port per network link (one port per traffic direction). For parallel monitoring (e.g. monitoring system plus portable decoder) it is also possible to double the monitoring ports exists.

LED Indicators
LED's on the front panel provide fast and easy indication of power-, link- and activity status.

Various Cabinet versions available
With the 19" Mount Kit you can build the portable TAP to flexible Cabinets. One TAP in 19", 1U; 2 different TAPs (SM and MM) to 19" and much more

Easy to use and operate
Easy operation and installation. No PC or software necessary. No bugs, no software- updates means more time for your business.

Different Power Versions
12VDC, 48VDC and also 230VAC versions available.

 
 
       
 © dhs ELMEA tools GmbH
 fon +49 6074 / 91 99 08 - 0  l  fax +49 6074 / 91 96 747  l  e-mail info@dhs-tools.de